fozzy
2nd Class Ticket
Posts: 8 
|
Post by fozzy on May 13, 2017 18:19:10 GMT
Stripped down engine today,got to dig deep into pockets.  Hub badly scored,brake shoes knackered,clutch plates and corks need replacing,etc.Engine stand was a cheap buy.  Good job iv'e got lots of time on my hands. |
|
fozzy
2nd Class Ticket
Posts: 8
|
Post by fozzy on May 27, 2017 17:05:57 GMT
Just built the engine back up to the head, when i found this in my tub of bits.I didn't change the bearing only the seal (what a dickhead).  |
|
|
|
Post by henri on May 28, 2017 6:51:23 GMT
oops , definitely looks to be a clutch bearing circlip .H
|
|
|
|
Post by mijapxman on May 28, 2017 13:10:27 GMT
fossy, most of us have done similar things in our time, at least you spotted it, before you put the engine back in the frame.
That's one of the reasons I don't like anyone around when I'm building/ tuning or assembling, not for hiding knowledge, but too easy to get distracted!.
Good luck with your build.
All the best.
Jim☺
|
|
|
|
Post by mushroom on May 28, 2017 15:43:12 GMT
I'm so forgetful I have to keep the sausage vid on and go through it step by step
|
|
fozzy
2nd Class Ticket
Posts: 8
|
Post by fozzy on Jun 3, 2017 20:37:12 GMT
Split the casing to put the main bearing circlip back in,replaced brake shoes,clutch corks and plates,fitted new hub.Hopefully finish it off tomorrow and put it back in the frame.   |
|
fozzy
2nd Class Ticket
Posts: 8
|
Post by fozzy on Jun 10, 2017 19:41:26 GMT
Undercoated the spacer for the wide tyre kit today,rattle can in the shed.I really need to get a proper spray gun.  |
|
|
|
Post by mijapxman on Jun 11, 2017 12:46:22 GMT
fozzy, looks like your getting there, keep up the good work.
I have a proper spray gun etc and only use it on big parts or if I have LOTS of small parts as I find it too much hassle setting it up and cleaning it afterwards.Spray cans work for me too!😀
All the best.
Mij☺
|
|
|
|
Post by ironsloth on Jun 11, 2017 14:50:36 GMT
Instead of using a spacer, couldn't you use two of the wider pieces of the rims together?
|
|
fozzy
2nd Class Ticket
Posts: 8
|
Post by fozzy on Jun 11, 2017 16:48:03 GMT
Cheers Face,got a spray gun at work which my brother in law is teaching me to use.The spacer is used to align the back wheel with the front,i bought it as a kit from SIP.The swing arm was cut to suit.
|
|
fozzy
2nd Class Ticket
Posts: 8
|
Post by fozzy on Jun 25, 2017 21:58:54 GMT
Finally the engine is back in the frame and the panel has been cut.Ordered a few parts from Beedspeed to replace the rusted ones.  |
|
|
|
Post by djloone on Jun 26, 2017 8:35:09 GMT
Lookin good  LOON-E |
|
soulboy73
2nd Class Ticket
All nighters and fast scoots is all I need
Posts: 15
|
Post by soulboy73 on Mar 11, 2018 10:17:01 GMT
Me likes that a lot
|
|
