|
Post by alisey on May 20, 2015 23:16:52 GMT
Nice one rab cheers for that
|
|
|
Post by henri on May 21, 2015 8:53:41 GMT
you jammy beggar , no more skinned knees or aching back, lookin good ,H
|
|
|
Post by alisey on Jun 6, 2015 19:47:39 GMT
|
|
|
Post by alisey on Jun 6, 2015 19:49:34 GMT
Centre piece floor mat
|
|
|
Post by alisey on Jun 6, 2015 19:51:36 GMT
Also got these bolt covers which are going on the front mudguard bolts, brake master, where they are in this pic and anywhere else where erm bolts are showing
|
|
|
Post by alisey on Jun 6, 2015 19:54:45 GMT
Front hubba hubba with disc attached
|
|
|
Post by alisey on Jun 6, 2015 20:04:18 GMT
|
|
|
Post by alisey on Jun 6, 2015 20:18:47 GMT
Oh and where do the indicators earth please? I'm guessing by the red circle, thanks
|
|
|
Post by henri on Jun 7, 2015 8:57:59 GMT
yep up on the springs/brackets youve circled , H
|
|
|
Post by alisey on Jun 7, 2015 12:19:11 GMT
Thanks H
|
|
|
Post by alisey on Jun 9, 2015 23:44:42 GMT
|
|
|
Post by rab on Jun 10, 2015 18:58:29 GMT
looking sexy always know your getting somewhere when its out of the shed and on its wheels again. personal choice but i would have taken the starter motor off and gone kick only.
|
|
|
Post by henri on Jun 11, 2015 7:37:10 GMT
i'm with rab , i like kicking scooters , does that make me a "bad man" , is lookin good , that green looks good in the sunshine , H
|
|
|
Post by alisey on Jun 11, 2015 20:23:04 GMT
It would be a hell of a lot easier to adjust the mixture screw if it wasnt there
Oh and once youve sooted the hell out of a plug are you best off sticking a new one in or can you save it??
Cheers
|
|
|
Post by rab on Jun 13, 2015 8:07:40 GMT
If in doubt change it out
|
|
|
Post by henri on Jun 14, 2015 10:05:18 GMT
as rab says , clean it with a brass wire brush n stick it in glovebox as a emergency spare , Hopefully never to be used , H
|
|
|
Post by alisey on Jun 22, 2015 11:43:03 GMT
Cheers guys
I broke the kickstart when I tried to use it without putting the bolt in - another part to be added to the shopping list.. doesn't seem to be getting shorter this list..
|
|
|
Post by djloone on Jul 9, 2015 22:02:48 GMT
Awesome looking fella...i will be starting a build thread of my own in the coming days..and will be picking your brains for help if you dont mind LOON-E
|
|
|
Post by alisey on Jul 14, 2015 17:08:45 GMT
Yes my man no worries - good luck with you build!
|
|
|
Post by alisey on Jul 14, 2015 18:17:26 GMT
Side Panel
Floor Runners
Num plate
Front Pan
Mirrors
Seat
|
|
|
Post by rab on Jul 14, 2015 21:17:01 GMT
bloody ell fella shes a stunna now fill it with chrome i took off my front rack today that's full of bling moved the scooter and nearly threw it across the road it was that light lol
|
|
|
Post by djloone on Jul 14, 2015 21:37:23 GMT
Looking cracking mate...what are the mirrors/where from..i like the look of them LOON-E
|
|
|
Post by alisey on Jul 15, 2015 12:14:30 GMT
okay will do Rab, send us over the rack and I'll get it bolted on for the show next weekend!
|
|
|
Post by alisey on Jul 15, 2015 12:28:53 GMT
Here's the link for the mirror Loon-e Right Hand Left Hand
Don't expect to see a lot out of them though, they vibrate so much it's a right challenge to figure out if someone's behind you! Here's another set I was looking at as well, a bit more going on with these ones. Right Hand Left Hand
|
|
|
Post by djloone on Jul 15, 2015 21:30:45 GMT
Cheers alisey..i will be looking into them LOON-E
|
|
|
Post by henri on Jul 17, 2015 7:47:05 GMT
lookin mighty sweet there alisey , greens not my colour but that is exceptionaly nice , just a tad jealous now , an if ya mirrors are shaking too much to see out of might be worn/tired anti-rattle washers on gear n throttle tubes lettin the tube rattle the bars about .if its just at tickover/standstill am afraid there aint nothin to cure that,they all do it . H
|
|
|
Post by fisher1977 on Jul 17, 2015 21:55:59 GMT
Absolutely awesome, bloody inspiring the results you can get. When do you stop spending money ?? Damn I'm gonna need a workshop. Great results, well done.
|
|
|
Post by alisey on Jul 18, 2015 7:44:21 GMT
Its when i ride henri, is there anyway i can find out where they SHOULD be? Im pretty sure mine was set up wrong before. And is it a case of buying some new ones or is there a repair/fix?
Thanks
|
|
|
Post by alisey on Jul 18, 2015 7:48:04 GMT
Stopping spending money? I didnt know that was an option!!
|
|
|
Post by henri on Jul 18, 2015 15:55:36 GMT
its always a option , specially if management starts readin the credit card statements , i went a bit all out/over the top when i did my daily hack , added up the receipts one day , when i came round an the buzzing in my ears stopped i vowed never to do that again , try the exploded diagrams on sips website to see order/amount of anti-rattles washers/shims on bars ,i cant remember on a p-series for sure ,but think on gear tube theres a shim between lever housing n headset ,an at inboard end theres 2 shims with a wavy anti-rattle between them then cable wheel, an on throttle its just the 2 shims n anti rattle .if you can slide bars in an out there missing the spacers or washers , dont think theres any plastic top hat bushes like cosas/t5/pk xl's . will look at sip n see , H
|
|